Skip to main content

Main parts of Jet Engine

Main parts of Jet Engine:

 

Fan - The fan is the first component in a turbofan. The large spinning fan sucks in large quantities of air. Most blades of the fan are made of titanium. It then speeds this air up and splits it into two parts. One part continues through the "core" or center of the engine, where it is acted upon by the other engine components.

The second part "bypasses" the core of the engine. It goes through a duct that surrounds the core to the back of the engine where it produces much of the force that propels the airplane forward. This cooler air helps to quiet the engine as well as adding thrust to the engine.

Compressor - The compressor is the first component in the engine core. The compressor is made up of fans with many blades and attached to a shaft. The compressor squeezes the air that enters it into progressively smaller areas, resulting in an increase in the air pressure. This results in an increase in the energy potential of the air. The squashed air is forced into the combustion chamber.

Combustor - In the combustor the air is mixed with fuel and then ignited. There are as many as 20 nozzles to spray fuel into the airstream. The mixture of air and fuel catches fire. This provides a high temperature, high-energy airflow. The fuel burns with the oxygen in the compressed air, producing hot expanding gases. The inside of the combustor is often made of ceramic materials to provide a heat-resistant chamber. The heat can reach 2700°.

Turbine - The high-energy airflow coming out of the combustor goes into the turbine, causing the turbine blades to rotate. The turbines are linked by a shaft to turn the blades in the compressor and to spin the intake fan at the front. This rotation takes some energy from the high-energy flow that is used to drive the fan and the compressor. The gases produced in the combustion chamber move through the turbine and spin its blades. The turbines of the jet spin around thousands of times. They are fixed on shafts which have several sets of ball-bearing in between them.

Nozzle - The nozzle is the exhaust duct of the engine. This is the engine part which actually produces the thrust for the plane. The energy depleted airflow that passed the turbine, in addition to the colder air that bypassed the engine core, produces a force when exiting the nozzle that acts to propel the engine, and therefore the airplane, forward. The combination of the hot air and cold air are expelled and produce an exhaust, which causes a forward thrust. The nozzle may be preceded by a mixer, which combines the high temperature air coming from the engine core with the lower temperature air that was bypassed in the fan. The mixer helps to make the engine quieter.



Labels:

Comments

Post a Comment

Popular posts from this blog

Aircraft Nose Cone

Why the Nose Cone in Aircraft is Important ?   Nose cone is also known as RADOME. As the Name Implies, it is the DOME which consists of Radar Equipment. The function of the radome is to protect the antennas installed in the nose of the aircraft from airflow, rain, hail, lightning strike, bird strike,etc. At the same time it must provide a radio-frequency transparent window, suitable for the microwave signals of the weather detection radar, instrument landing system and microwave landing system. The most demanding system in terms of radome radio frequency specification is the weather radar.   Nose Cone/Radome Sources of radome degradation   There are many reasons for the performance level of a radome to degrade below minimum requirements. They range from lightning strike, bird strike, natural erosion, water ingress for some types of radomes, ageing, poor, repairs such as wrong material used, or over-painting.   How a degraded radome affects t...
Post a Comment
Read more

737 Max Recertification Process

As we all know the Recertification flight test for 737 max completed on 1-July-20. This is 737-7 Aircraft. As per the FAA below are the list of process further required to ungrounding of the Aircraft. But this is applicable only to US, each country's regulator has to approve it to make sure Max is flying safe only then it is allowed in their Airspace. The remaining tasks include: JOEB Validation & FSB Review  – The FAA’s Flight Standardization Board (FSB) and the Joint Operations Evaluation Board (JOEB) which includes international partners from Canada, Europe, and Brazil will evaluate minimum pilot training requirements.  The FSB will issue a draft report for public comment addressing the findings of the FSB and JOEB. Final FSB Report  – The FAA will publish a final FSB report after reviewing and addressing public comments. Final Design Documentation and TAB Report  – The FAA will review Boeing’s final design documentation in order to evaluate compliance with al...
Post a Comment
Read more

Jet Engine - How it works

All jet engines, which are also called gas turbines, work on the same principle. 1. The engine sucks air in at the front with a fan. 2. A compressor raises the pressure of the air. The compressor is made with many blades attached to a shaft. 3. The blades spin at high speed and compress or squeeze the air. 4. The compressed air is then sprayed with fuel and an electric spark lights the mixture. 5. The burning gases expand and blast out through the nozzle, at the back of the engine. As the jets of gas shoot backward, the engine and the aircraft are thrust forward. As the hot air is going to the nozzle, it passes through another group of blades called the turbine. The turbine is attached to the same shaft as the compressor. Spinning the turbine causes the compressor to spin. The air goes through the core of the engine as well as around the core. This causes some of the air to be very hot and some to be cooler. The cooler air then mixes with the hot air at the engine exit area. ...
Post a Comment
Read more